Easy-To-Follow Pressure-Side Pool Cleaner Troubleshooting Guide And Tips
One of the best investments you can get for your backyard pool is a pressure-side cleaner. It enables you to save plenty of time since using it will eliminate the necessity to vacuum and skim your pool manually.
Moreover, this variety of automatic pool cleaner is not only convenient and effective, but it also does not require external power to operate. But no matter how exceptional or high-end your pressure cleaner is, it will sometimes malfunction just like with all mechanical gadgets.
When this happens, do not abandon your device and return to cleaning your backyard mecca manually. Check your equipment first and figure out where the problem originates, and then follow these simple DIY troubleshooting tips.
Why Is My Pool Cleaner Seem To Not Move At All?
For your pressure pool cleaner to operate, it requires approximately 30 PSI. However, low-pressure types will only require roughly 17 PSI. If your device is not moving, check if both your filter pump and booster pump are working all together.
Moreover, your automatic cleaner comes with an inline strainer or two, which you need to clean periodically. This component is usually located in the wall connection fitting or feed hose of your unit. Your cleaner has small components that can get clogged easily with small bits of sand. This, in return, can prevent it from maneuvering around.
Your unit may also find it hard to move when there are sand or pebbles caught in its wheels. Moreover, the power train of your pressure-side, which is either belt, chain, or shaft-driven, can experience problems.
To check, rotate either one of the wheels of your device. If the other one also rotates simultaneously with the other, then they are working just fine.
My Pressure Cleaners Is Constantly Getting Stuck On Steps
One of the things you can do if you see your pressure cleaner is constantly caught on your pool stairs or steps is to try adjusting the thrust jet.
Doing this will form a new washing pattern for your unit. Likewise, you can change the cleaning direction of the machine by giving its float hose a little adjustment. You can also try adding hose weights.
Furthermore, your hose will tangle and twist if you store it coiled tightly or if you hang it on a hook throughout the cold months. This will make it harder to straighten up.
To resolve this, what you need to do is stretch out your hose along your pool deck under the sun. If necessary, you can utilize some weights to hold it down. This and the warmth of the sun can help straighten it up.
Damaged Booster Pump
A pressure-side cleaner typically has a return line attached to it, which should give your device with a substantial amount of pressure. If the pressure it’s producing is not right, then you may have a problem with the filter, pool pump, or booster pump.
Check if the problem is originating from either the pool pump or filter. Once you verify that those were not the culprit, shift your focus to your booster pump. Repairing a booster pump can put a little dent in your wallet and will take a long time. Hence, you may want to reconsider and replace it instead. Not only will this save you time, but it’ll not be as expensive.
When replacing your booster pump, ensure that its parameters match those of your old one. If you have a Polaris pressure cleaner, purchase parts from the Zodia brand, which is the parent company of Polaris.
Additionally, check out this best pressure-side pool cleaner buyer’s guide and reviews by Luke Reed (Cleanup.Expert magazine). The article will provide you with an in-depth look at pressure pool cleaners.
There’s A Leak In My Float Hose
An automatic pool cleaner sucks in both water and filth. All the grime it collects will be deposited in its filter container. On the other hand, the water, which has been refined at this point, goes back into your pool via the cleaner’s float hose. This hose is connected to the return jet and pressure cleaner.
Your device will not get plenty of pressure if there’s a leak on the float hose, which may also cause it to stop running. Fixing this is easy. Simply seal any leaks with the help of waterproof tape.
The solution is temporary so you can continue washing your pool. So don’t forget to replace it afterward, especially if there are plenty of leaks.
The wheels of your pressure-side cleaner have drive belts for turning the wheels. So when these get busted or snap, your device will stop moving. If the back-up valve of your unit is functioning and the tail is waiving around but the wheels are not turning, then you have a broken belt.
To see if this is the issue, take your equipment out of the swimming pool. Check if every wheel will rotate. Locate its belts and check if there are any damages. If you find any damage, you need to replace them since they’re irreparable.
Leak In The Back-Up Valve
You’ll find some pressure cleaners that feature a back-up valve together with a nozzle. This releases bursts of high-pressure water that helps the cleaner maneuver throughout your pool as it clears your water with filth. When the back-up valve has leaks, it’ll spray water out of it instead. If this is the case, you have no other choice but to replace the component.
Troubleshooting your pressure-side pool cleaner is not that hard. Just make sure to analyze the problem first so that you can apply the proper solution.
Keep in mind that before installing your unit, your need to clean your pool filter first. Likewise, always remove cleaner before chemically treating the pool. Knowing the proper ways to maintain your pool cleaner can help prevent problems and help prolong its life as well.